Comtech EF Data LPOD Especificações Página 83
- Página / 218
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
LPOD C-, X-, or Ku-Band Outdoor Amplifier / Block Up Converter MN-LPOD
Ethernet-based Remote Product Management Revision 10
4–19
Amplifier
• Amplifier – Use the drop-down list to select the amplifier as either On or Off.
• Attenuation (dB) – Enter a valid attenuation level (00.00 to 20.00 dB) in 0.25 dB steps.
• Attenuation Offset – Enter a valid value, in dB, for the attenuation offset.
• Fault Recovery – Use the drop-down list to select Fault Recovery as either Automatic or
Manual.
• Mute – Use the drop-down list to select the Mute function as either Enabled or Disabled.
• AUX Mute – Use the drop-down list to select the Auxiliary Mute Mode as either Enabled or
Disabled.
• Offline Mute – Use the drop-down list to select the Offline Mute function as Enabled,
Disabled, MuteRx, MuteTx, MuteRx+LNB, or MuteTx+LNB.
Click [Change Configuration] to save any changes. Otherwise, click [Reset] to revert to the
previously assigned Amplifier settings.
Reference
• Ref Freq Adjust – Enter a numeric value from 0 to 255 to adjust the reference oscillator
tuning voltage. The default value is set to 87.
• Ext Ref Mute – Use the drop-down list to select the Eexternal Reference Not Present Mute
Mode as either Enabled or Disabled.
Click [Change Configuration] to save any changes. Otherwise, click [Reset] to revert to the
previously assigned Reference settings.
Low Power Forward Threshold (dBm)
Use this field to set the threshold value, in dBm, for the low forward power alarm/fault. When
the forward power monitor is set to Alarm or Fault instead of the factory default of Mask, and
the forward power drops below the specified value, the alarm/fault is indicated.
Setting this parameter to the default value of 00.00 effectively disables the threshold.
Click [Change] to save any changes. Otherwise, click [Reset] to revert to the previously assigned
Low Power Forward Threshold setting.
FSK Address
Use this field to set the FSK (Frequency Shift Keying) Address from 01 to 15. Click [Change] to
save any changes. Otherwise, click [Reset] to revert to the previously assigned FSK Address.
- Revision 10 1
- Part Number MN-LPOD 3
- Revision 10 3
- TABLE OF CONTENTS 5
- vii 9
- FIGURES 10
- PREFACE 13
- Electrical Safety Notice 14
- Product Support 15
- Preface Revision 10 16
- Chapter 1. INTRODUCTION 19
- 1.2 Functional Description 20
- 1.3 Features 20
- 1.3.7 Optional LNB Support 21
- 1.4 Theory of Operation 22
- 1.4.1 SSPA Block Diagrams 22
- 1.4.2 SSPA Module 23
- 1.4.3 Cooling System 24
- 1.4.5 LNB Operation 24
- 1.4.6 Power Supply 24
- BUC C, Ku, X LO Frequencies 25
- 1.5.1 Characteristics 26
- 1.5.4 Environmental 28
- 1.5.5 Physical 28
- 1.6 Dimensional Envelopes 30
- Introduction Revision 10 31
- Chapter 2. SYSTEM 41
- CONNECTIONS, INSTALLATION 41
- STARTUP 41
- 2.3 Interface Connectors 44
- Control Port) 48
- 2.3.8 Ground Connector 49
- 2.5 Power-up the LPOD 50
- Chapter 3. UPDATING FIRMWARE 55
- Chapter 4. ETHERNET-BASED 65
- REMOTE PRODUCT 65
- 4.3 SNMP Interface 66
- 4.3.3 SNMP Traps 67
- 4.4 Telnet Interface 70
- Enter the LPOD’s 71
- 4.5.2 User Login 73
- 4.5.3.1 Menu Tree 74
- 4.5.3.2 Page Navigation 74
- 4.5.3.3 Page Sections 74
- 4.5.3.4 Action Buttons 75
- 4.5.3.5 Drop-down Lists 75
- 4.5.3.6 Text or Data Entry 75
- 4.5.4.1 Home Pages 76
- 4.5.4.1.1 Home 76
- 4.5.4.1.2 Home 77
- 4.5.4.1.3 Home 78
- 4.5.4.2 Admin Pages 79
- 4.5.4.2.1 Admin 79
- Webpage Timeout 80
- 4.5.4.2.2 Admin 81
- 4.5.4.3 Config Pages 82
- 4.5.4.3.2 Config 84
- 4.5.4.3.3 Config 85
- Redundancy 87
- Online Status 87
- Force Online 87
- 4.5.4.4 Status Pages 88
- 4.5.4.4.1 Status 88
- 4.5.4.4.2 Status 89
- 4.5.4.4.3 Status 90
- 4.5.4.4.4 Status 91
- Alarm Mask 92
- Statistics Configuration 94
- 4.5.4.4.6 Status 95
- Control Bar and Refresh Tab 96
- Temperature Graph 97
- Power Graph 97
- LNB Current Graph 98
- Amplifier Status Graph 98
- Mute State Graph 98
- Online Status Graph 99
- Minimum Fan Speed Graph 99
- MANAGEMENT 101
- 5.2.2 Attenuator Control 102
- 5.2.3 Mute Control 102
- 5.2.4 Faults 102
- 5.2.5 Power Detector 104
- 5.2.6 Some Common Commands 104
- 5.2.7 End-of-Life Commands 104
- 5.1.1 EIA-485 105
- 5.1.2 EIA-232 106
- 5.1.3 Basic Protocol 106
- 5.1.4 Packet Structure 106
- 5.1.4.1 Start of Packet 107
- 5.1.4.2 Target Address 107
- 5.1.4.3 Address Delimiter 107
- 5.1.4.4 Instruction Code 108
- 5.1.4.7 End of Packet 109
- Appendix A. 1:1 REDUNDANCY 137
- Appendix A Revision 10 138
- A.5.1 Common Kit Examples 146
- BLANK PAGE 151
- Appendix B. CABLE DRAWINGS 193
- B.2 Control and Data Cables 194
- Appendix B Revision 10 195
- B.3 RF Cables 202
- B.3.1 RF Cable (Type ‘N’) 203
- Appendix C. MAINTENANCE 205
- Appendix C Revision 10 206
- 212
- 480 • 333 • 2200 PHONE 218
- • 333 • 2161 FAX 218
Manuais e produtos relacionados com Amplificadores áudio Comtech EF Data LPOD
(60 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais