Comtech EF Data CDM-710L Especificações Página 126
- Página / 242
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CDM-710 Broadcast Satellite Modem Revision 11
Ethernet Management MN/CDM710.IOM
6–6
response (for example, FRW? response) will be displayed as one line, with the latter lines overwriting
the previous lines.
In order to view the full response messages, CEFD recommends using HyperTerminal configured
as Telnet Client. To do so, configure HyperTerminal as follows:
1. Ensure that connection is made
using TCP/IP (Winsock)
instead of COM1 or COM2, as
shown in the example to the near
right.
2. ASCII Setup (File Æ Properties
Æ Settings Æ ASCII Setup):
Check the "Send line ends with
line feeds" option in the ASCII
Sending section and the
"Append line feeds to
incoming line ends" option in
the ASCII Receiving section, as
shown in the example to the far
right.
Login and remote command execution via HyperTerminal configured as Telnet Client appears as
per the following examples:
- CDM-710 1
- Errata A 3
- Table of Contents 9
- Figures 18
- PREFACE 19
- Preface MN/CDM710.IOM 20
- Installation 21
- Environmental 21
- CE Mark 22
- RoHS Compliance 22
- Warranty Policy 23
- Limitations of Warranty 23
- Exclusive Remedies 24
- Customer Support 25
- Online Customer Support 25
- Chapter 1. INTRODUCTION 27
- 1.2 Functional Description 28
- Introduction MN/CDM710.IOM 29
- 1.3.1 Physical Description 30
- 1.3.2 Major Assemblies 31
- 1.3.3 Dimensional Envelope 32
- 1.3.4 Physical Features 33
- 1.3.4.1 Front Panel 33
- 1.3.4.2 Rear Panel 34
- 1.3.6 Verification 36
- FAST System Theory 37
- FAST Implementation 37
- FAST Accessible Options 37
- Figure 1-7. Spectral Mask 40
- 1.4.2 Modulator 41
- 1.4.2.1 CDM-710 (70/140 MHz 41
- ) Modulator 41
- 1.4.3 Demodulator 42
- Maximum Level 43
- Minimum Level 43
- 1.4.4 Test Functions 45
- 1.4.5 Monitor Functions 45
- 1.4.6 Remote Port Operation 45
- 1.4.7 Data Rate Range 46
- Chapter 2. INSTALLATION 49
- 2.2 Mounting 50
- Installation MN/CDM710.IOM 51
- Chapter 3. REAR PANEL 53
- CONNECTORS 53
- PINOUTS 53
- 3.2.1 Tx IF Connectors, J1 55
- 3.2.2 Rx IF Connectors, J3 55
- 3.4 Utility Connections 56
- 3.4.1 Alarms Connector, P1 56
- 3.5 Power/Ground Connectors 58
- Chapter 4. FLASH UPGRADING 59
- IMPORT ANT 60
- 4.5 USB Procedure 63
- Chapter 5. FRONT PANEL 65
- OPERATION 65
- 5.1.2 Front Panel Keypad 67
- 5.2 Opening Screen 68
- 5.2.1 Menu Matrix 69
- 5.3 SELECT: (Main) Menu 70
- 5.3.1 SELECT: Config 71
- (CONFIG: Remote) Local 72
- (CONFIG: Remote) Serial 72
- (CONFIG: Remote) Ethernet 73
- ENTER when done 74
- (CONFIG: Tx) Mod 76
- (CONFIG: Tx:) Mod Æ Type 76
- (CONFIG:Tx) Mod Æ Inv 76
- (CONFIG: Tx) Mod Æ α 77
- (CONFIG: Tx) Code 78
- (CONFIG : Tx) SymRate 78
- (CONFIG: Tx) Mode 80
- (CONFIG: Tx) Frequency 81
- (CONFIG: Tx) Pwr 81
- (CONFIG: Tx) Pwr Æ Level 82
- (CONFIG: Tx) Pwr Æ On/Off 82
- (CONFIG: Tx) Pwr Æ Imped 82
- 5.3.1.3 (CONFIG:) Rx 83
- (CONFIG: Rx) FEC 83
- (CONFIG: Rx) Dem (Demod) 83
- (CONFIG: Rx) Dem Æ Type 83
- (CONFIG: Rx) Dem Æ Inv 84
- (CONFIG: Rx) Dem Æ Acq 84
- (CONFIG: Rx) Dem Æ α 84
- (CONFIG: Rx) Dem Æ Eq 84
- (CONFIG: Rx) Dem Æ IQ-TP 85
- (CONFIG: Rx) Code 85
- (CONFIG: Rx) SymRate 86
- (CONFIG: Rx) Mode 86
- (CONFIG: Rx) Freq 86
- (CONFIG: Rx) Eb/No 87
- (CONFIG: Rx) PLL 87
- Interface 2 88
- (CONFIG: Intfc1 ASI) Config 89
- (CONFIG: Intfc1 HSSI) Tx 90
- ENTER 93
- • Normal: CTS = RTS 93
- ENTER. Enable is selected to 97
- ENTER. Enable is 97
- ENTER or CLEAR when done 99
- 5.3.1.7 (CONFIG:) Ref 101
- 5.3.1.8 (CONFIG:) Aux 101
- (CONFIG: Aux) Auto/Manual 101
- (CONFIG: Aux) Ena/Dis 102
- (CONFIG: Aux) FORCE(1:1) 102
- 5.3.1.9 (CONFIG:) Alarms 102
- (CONFIG: Alarms) Tx 102
- 5.3.2 SELECT: Monitor 103
- 5.3.2.1 (Monitor:) Alarms 103
- (Monitor: Alarms) Transmit 103
- (CONFIG: Alarms) Intfc1 103
- (Monitor: Alarms) Receive 104
- (Monitor: Alarms) Unit 104
- 5.3.2.2 (Monitor:) Rx_Stats 106
- (Monitor:) Event-Log Æ View 107
- 5.3.3 SELECT: Test 107
- 5.3.3.1 (Test:) Mode 107
- (Available Some Interfaces) 109
- 5.3.4 SELECT: Info 110
- 5.3.4.1 (INFO:) Rem 110
- 5.3.4.2 (INFO:) Tx 111
- 5.3.4.3 (INFO:) Rx 111
- 5.3.5 SELECT: Save/Load 113
- 5.3.5.1 (Save/Load:) Save 113
- 5.3.5.2 (Save/Load:) Load 114
- 5.3.6.1 (UTIL:) RT-Clk 114
- 5.3.6.2 (UTIL:) Ref 115
- 5.3.6.3 (UTIL:) ID 115
- 5.3.6.4 (UTIL:) Display 115
- 5.3.6.5 (UTIL:) Firmware 115
- (Firmware:) Info 116
- (Firmware:) Info Æ Bootrom 116
- (Firmware:) Select 116
- 5.3.6.6 (UTIL:) FAST 118
- (FAST:) Cnfg (Configuration) 118
- (FAST:) Cnfg Æ Code 118
- (FAST:) Cnfg Æ Demo Mode 118
- (UTIL:) FAST Æ View 119
- Chapter 6. ETHERNET 121
- MANAGEMENT 121
- IMPORTANT 122
- 6.3.1.1 Common Private MIBs 123
- 6.3.1.3 ASI Private MIB 123
- 6.3.1.6 HSSI MIB 124
- 6.3.3 SNMP Traps 124
- 6.4 Telnet Interface 125
- 6.4.2 Using Telnet 127
- 6.4.3 Telnet Examples 127
- 6.5.2 User Login 128
- 6.5.3 Web Server Menu Tree 129
- 6.5.4.1 Home Page 130
- Select Boot Image 139
- Perform Soft Reboot 139
- Chapter 7. FORWARD ERROR 145
- CORRECTION OPTIONS 145
- 7.3.1 Range of Data Rates 146
- Eb/No (dB) 150
- DVB-S: QPSK BER vs Eb/No 150
- Es/No (dB) 153
- DVB-S2: 8-PSK PER vs Es/No 154
- Chapter 8. CDI-40 ASI 157
- INTERFACE MODULE 157
- 8.2.1 Connector Pinouts 159
- 8.3 Functional Description 160
- 8.3.1.1 MPEG-2 Null Packet 160
- 8.3.3 1:1 Applications 161
- 8.4 General Specifications 162
- Chapter 9. CDI-60 HSSI 163
- 9.2 Physical Description 164
- 9.2.1 Connector Pinout 165
- Continuous Clock 166
- Gap Clock 166
- GIGABIT ETHERNET (GigE) 167
- Gigabit Ethernet Card 168
- MPEG COP3 Annex A) 170
- Appendix A. REMOTE CONTROL 175
- A.3 EIA-232 176
- A.4 Basic Protocol 176
- A.5.3 Address Delimiter 178
- A.5.4 Instruction Code 178
- A.5.7 End Of Packet 179
- Appendix A MN/CDM710.IOM 180
- A–6 180
- A.6.1 Modulator 181
- A–8 182
- A–9 183
- A–10 184
- A–11 185
- A–12 186
- A–13 187
- A–14 188
- A–15 189
- A–16 190
- A–17 191
- A–18 192
- A–19 193
- A.6.2 Demodulator 194
- A–21 195
- A–22 196
- A–23 197
- A–24 198
- A–25 199
- A–26 200
- A–27 201
- A–28 202
- N/A 5 bytes Query only 203
- A–30 204
- A–31 205
- A–32 206
- A.6.3 Modem 207
- A–34 208
- A–35 209
- A–36 210
- A.6.4 Priority System 211
- A–38 212
- A–39 213
- A–40 214
- A–41 215
- A–42 216
- A–43 217
- A–44 218
- A–45 219
- A–46 220
- A–48 222
- A–49 223
- A–50 224
- A–51 225
- A.6.5.1 MGC Format 226
- A–53 227
- A–54 228
- A–55 229
- A–56 230
- Appendix B. Eb/No 231
- MEASUREMENT 231
- ((Co+No)/No)/10) 232
- Appendix C. FAST ACTIVATION 237
- PROCEDURE 237
- UTILITY Æ FAST menu: 239
- Cnfg, then press [ENTER]: 239
- C.3 Using FAST Demo Mode 240
- METRIC CONVERSIONS 241
- Units of Length 241
- Temperature Conversions 241
- Units of Weight 241
- 480 • 333 • 2200 PHONE 242
- • 333 • 2161 FAX 242
Manuais e produtos relacionados com Redes Comtech EF Data CDM-710L
Redes Comtech EF Data CIM-550 Especificações
(460 páginas)
(460 páginas)
Redes Comtech EF Data CDD-880 Especificações
(124 páginas)
(124 páginas)
Redes Comtech EF Data CDM-840 Especificações
(244 páginas)
(244 páginas)
Redes Comtech EF Data SDM-100A Especificações
(212 páginas)
(212 páginas)
Redes Comtech EF Data CDM-Qx Especificações
(258 páginas)
(258 páginas)
Redes Comtech EF Data CDM-Qx Especificações
(260 páginas)
(260 páginas)
Redes Comtech EF Data CDM-700 Especificações
(266 páginas)
(266 páginas)
Redes Comtech EF Data CDD-880 Manual do Utilizador
(34 páginas)
(34 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais