Comtech-ef-data CRS-500 Manual do Utilizador Página 134
- Página / 218
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CRS-500 1:N Redundancy System Revision 2
CSU Front Panel Operation MN-CRS500
7–18
• If the second power supply module is not needed, you can mask this alarm.
Example 3:
Switch Alarm: RM Problem
RM I/O Timeout
There is a fault. Communication has been lost to the Redundant Modem. The front panel LED
“Unit Status” will be red.
Suggestions:
• Check Cable Connections – refer to Chapter 4. CABLES AND CONNECTIONS.
• Check Modem Configurations – refer to Chapter 6. CONFIGURING MODEMS FOR
1:N REDUNDANCY.
Example 4:
Switch Alarm: RM Problem
MGC refused, code:12 TFT
There is a fault. COMMs are good to the Redundant Modem, but the configuration of the
bridged Traffic Modem cannot be configured into the Redundant Modem. The front panel LED
“Unit Status” will be red.
Suggestion: Ensure that the most capable modem – with regard to FAST options, installed
options, etc. (e.g. Turbo card, firmware version, and hardware revision) – is used as the
Redundant Modem. The code indicates the parameter within the MGC configuration string that
is causing rejection by the Redundant Modem. The three-letter instruction code is indicated also
to assist you in decoding the problem parameters.\
7.2.2.3.2 STATUS: Events (Stored Events)
Stored Events: View
Clear-all
Use the ◄ ► arrow keys to select View or Clear-All, and then press ENTER.
If Clear-All is selected, the event log is cleared and you are taken directly back to the previous
menu. However, if there are faults present on the unit at this time, new log entries will be
generated for those faults.
- CRS-500 1
- Errata A 3
- TABLE OF CONTENTS 7
- Table of Contents MN-CRS500 10
- FIGURES 14
- PREFACE 17
- Metric Conversion 18
- Safety and Compliance 19
- Electrical Installation 19
- Operating Environment 20
- (2004/108/EC) 20
- <HAR> 21
- (91/263/EEC) 22
- CE Mark 22
- Warranty Policy 22
- Limitations of Warranty 22
- Exclusive Remedies 23
- Getting Help 24
- Contacting Comtech EF Data 24
- Preface MN-CRS500 25
- Chapter 1. INTRODUCTION 27
- Introduction MN-CRS500 28
- 1.2 Features 30
- 1.3.1.1 CSU Front Panel 32
- 1.3.1.2 CSU Rear Panel 33
- Supply Modules 33
- 1.3.2.1 DSU Front Panel 35
- 1.3.2.2 DSU Rear Panel 36
- 1.3.2.3.1 RMI Modules 37
- 1.3.2.3.2 TMI Modules 38
- CONFIGURATION CHECK LISTS 47
- 2.2 Initial Start-up 48
- R edundancy S ys tem 49
- Redundancy System 50
- Chapter 3. INSTALLATION 53
- Installation MN-CRS500 54
- Chapter 4. CABLES AND 57
- CONNECTIONS 57
- Connections 61
- 4.3 Modem Connections 65
- Cable Connections 68
- (CnC) Data Connections 74
- (CnC) Operation 87
- 4.4 IF Cable Connections 89
- 4.4.1 IF Cabling Overview 89
- Configurations 91
- 4.5 Power Connections 97
- 4.5.1 Overview 97
- Chapter 5. UPDATING FIRMWARE 101
- Updating Firmware MN-CRS500 102
- Chapter 6. CONFIGURING 111
- 1:N REDUNDANCY 111
- ONLY if the DoubleTalk 114
- CSU FRONT PANEL OPERATION 117
- 7.1.2 6-Button Keypad 119
- 7.1.3 LED Indicators 120
- 7.2.2.1.2 CONFIG: Manual 126
- 7.2.2.1.3 CONFIG: IP 126
- CONFIG: IP SNMP Read 127
- CONFIG: IP SNMP Write 127
- 7.2.2.1.4 CONFIG: Remote 128
- 7.2.2.1.5 CONFIG: Options 129
- Backup Holdoff: 05 sec 130
- Restore Holdoff: 10 sec 130
- Alarm Mask: Modem-Alarms 130
- Switch-Alarms Audio 130
- 7.2.2.2.7 Info: IF-SW 133
- 7.2.2.3 SELECT: Status 133
- 7.2.2.3.1 STATUS: Alarms 133
- AND CONNECTIONS 134
- 7.2.2.4 SELECT: UTILITY 136
- 7.2.2.4.3 UTIL: Firmware 136
- Chapter 8. ETHERNET-BASED 139
- REMOTE PRODUCT 139
- MANAGEMENT 139
- 8.3 SNMP Interface 140
- 8.4 Telnet Interface 142
- 8.5.1 User Login 144
- 8.5.2.1 Menu Tree 145
- 8.5.2.2 Page Navigation 145
- 8.5.2.3 Page Sections 145
- 8.5.2.4 Action Buttons 145
- 8.5.2.5 Drop-down Lists 146
- 8.5.2.6 Text or Data Entry 146
- 8.5.3.1 Home (Splash) Page 147
- Redundancy Configuration 148
- Alarm Masks 150
- 8.5.3.2.2 Config 151
- 8.5.3.3 Status pages 154
- 8.5.3.3.1 Status 154
- Clear Event Log 155
- 8.5.3.4 Utility pages 156
- 8.5.3.4.1 Utility 156
- NTP Configuration 157
- Bulk Information (read-only) 157
- Firmware Image Select 158
- 8.5.3.4.3 Utility 159
- 9.2 EIA-485 162
- 9.3 EIA-232 163
- 9.4 Basic Protocol 163
- 9.4.2 Packet Structure 165
- 9.4.2.1 Start Of Packet 165
- 9.4.2.2 Target Address 166
- 9.4.2.3 Address Delimiter 166
- 9.4.2.4 Instruction Code 167
- 9.4.2.7 End Of Packet 168
- 9.5.1 Table Indexes 169
- Appendix A. CABLE DRAWINGS 183
- A.2 User/Utility Cables 184
- A.3 Control Cables 185
- Appendix A MN-CRS500 186
- A.4 Data / IF Cables 190
- A.4.2 Multi-drop CnC 192
- A.4.5 IF Cable (75Ω BNC) 195
- A.4.7 IF Cable (50Ω BNC) 197
- CONNECTORS 199
- PINOUTS 199
- Appendix B MN-CRS500 200
- (RJ-45F) 206
- Appendix C. ADDRESSING 209
- SCHEME INFORMATION 209
- Appendix C MN-CRS500 210
- C.2.2 Setting Up Modems 213
- C.3 M&C Applications 215
- 480 • 333 • 2200 PHONE 218
- • 333 • 2161 FAX 218
Manuais e produtos relacionados com Equipamento Comtech-ef-data CRS-500
Equipamento Comtech-ef-data CRS-311 Manual do Utilizador
(196 páginas)
(196 páginas)
Equipamento Comtech-ef-data RCS11 Manual do Utilizador
(110 páginas)
(110 páginas)
Equipamento Comtech-ef-data RCS20 Manual do Utilizador
(202 páginas)
(202 páginas)
Equipamento Comtech-ef-data CRS-300 Manual do Utilizador
(300 páginas)
(300 páginas)
Equipamento Comtech-ef-data CDS-100 Manual do Utilizador
(138 páginas)
(138 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais