Comtech-ef-data CDM-740 Manual do Utilizador Página 54
- Página / 150
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CDM-740 Advanced Satellite Modem Revision 0
Front Panel Operation MN-CDM740
5–2
5.1.1 Front Panel LED Indicators
IMPORTANT
In general, the Alarm relay state will reflect the state
of the Front Panel LEDs. For instance, if the Unit
Status LED is red, the Unit Alarm relay will be active,
etc. The one exception is the Transmit Traffic relay.
This will only be activated if a Transmit Traffic Fault
exists – it does not reflect the state of the Tx carrier.
The function of the eight front panel LED indicators is as follows:
LED Condition
UNIT STATUS
Green No Unit Faults, or Traffic Faults
Amber No Unit Faults, but a Traffic Fault exists
Red A Unit Fault exists (Example: PSU fault)
TRANSMITTER ON
Green Transmitter is ON
Off Transmitter is OFF. May be forced OFF by a Fault or programmed OFF
Tx TRAFFIC
Green No Tx Traffic Faults (data, encoder, synthesizer and modulator all OK)
Off A Tx Traffic fault exists
ONLINE
Green The Unit is Online, and carrying traffic
Off The Unit is Offline (standby) – forced by externally connected 1:1 redundancy system
STORED EVENT
Amber
There is a Stored Event in the log, which can be viewed from the front panel, or retrieved
via the remote control interface
Off There are no Stored Events
Rx-1 TRAFFIC
Green No Rx-1 Traffic Faults (demod-1 and data are all are OK)
Off
An Rx-1 Traffic fault exists (the demod may still be OK)
Or Rx-1 is inactive and not enabled (programmed OFF)
Rx-2 TRAFFIC (Unused) (Unused)
TEST MODE
Amber A Test Mode is selected (Example: TX CW)
Off There is no currently selected Test Mode
5.1.2 Front Panel Keypad
IMPORTANT
The keypad has an auto-repeat feature. If a key is held
down for more than 1 second, the key action will repeat,
automatically, at the rate of 15 keystrokes per second.
This is particularly useful when editing numeric fields,
with many digits, such as frequency or data rate.
The function of the keypad is as follows:
◄ ► (Left, Right)
These arrows are used to move to the next selection or to move the cursor functions.
At times, they may also used to move from one section to another.
▲ ▼ (Up, Down)
These arrows are used primarily to change configuration data (numbers).
At times, they may also be used to move from one section to another.
ENTER
This key is used to select a displayed function or to execute a modem configuration change.
CLEAR
This key is used to back out of a selection or to cancel a configuration change which has not been
executed using [ENTER]. Pressing [CLEAR] generally returns the display to the previous selection.
- Advanced Satellite Modem 1
- Errata A 3
- Errata Page 2 of 4 4
- Errata Page 3 of 4 5
- Errata Page 4 of 4 6
- CDM-740 7
- Table of Contents 9
- Table of Contents MN-CDM740 10
- Figures 15
- PREFACE 17
- Preface MN-CDM740 18
- Low Voltage Directive (LVD) 19
- Installation 19
- Environmental 19
- CE Mark 20
- RoHS Compliance 20
- Warranty Policy 21
- Limitations of Warranty 21
- Exclusive Remedies 22
- Customer Support 23
- Online Customer Support 23
- Chapter 1. INTRODUCTION 25
- 1.2 Functional Description 26
- Introduction MN-CDM740 27
- 1.3 Features 28
- 1.3.1 Physical Description 28
- 1.3.2 Compatibility 28
- 1.3.3 Major Assemblies 28
- 1.3.4 Dimensional Envelope 29
- 1.3.5 Physical Features 30
- 1.3.5.1 Front Panel 30
- 1.3.6 Rear Panel 31
- 1.3.7 Data Interfaces 31
- 1.3.8 Verification 31
- FAST System Theory 32
- FAST Implementation 32
- FAST Accessible Options 32
- 1:1 Redundancy Applications 33
- 1.4 New in this Release 33
- 1.5.1 Transmit / Modulator 34
- 1.5.3 Data Interfaces 36
- 1.5.4 Data Rate Ranges 36
- 1.5.5 Miscellaneous 37
- 1.5.6 Approvals 37
- Chapter 2. INSTALLATION 39
- 2.2 Mounting 40
- Installation MN-CDM740 41
- Chapter 3. REAR PANEL 43
- CONNECTOR PINOUTS 43
- CA UTION 45
- 3.4 Utility Connections 46
- 3.4.1 TERM Connector, RJ-12 46
- Chapter 4. FLASH UPGRADING 49
- Flash Upgrading MN-CDM740 50
- ... Please wait 51
- SELECT: 52
- Utility Æ Firmware Æ Select 52
- Chapter 5. FRONT PANEL 53
- OPERATION 53
- 5.1.2 Front Panel Keypad 54
- 5.2.1 Opening Screen 55
- 5.2 Front Panel Menu 55
- 5.3 SELECT: (Main) Menu 57
- 5.4 SELECT: Configuration 58
- 5.4.1 CONFIG: Tx 58
- 5.4.1.1 (CONFIG:) Tx Æ IF 58
- 5.4.1.4 (CONFIG:) Tx Æ FEC 59
- 5.4.1.6 (CONFIG:) Tx Æ Data 60
- 5.4.2 CONFIG: Rx 61
- 5.4.2.1 (CONFIG:) Rx Æ IF 61
- 5.4.2.3 (CONFIG:) Rx Æ FEC 61
- 5.4.2.5 (CONFIG:) Rx Æ Data 62
- Rx Descrambling Index: 63
- Rx Demod Pilot: Off On 63
- (◄►E) 63
- 5.4.3 CONFIG: Clocks 66
- 5.4.4 CONFIG: Remote 67
- 5.4.5 CONFIG: IP 67
- 5.4.6 CONFIG: Misc 70
- 5.5 SELECT: Test 71
- 5.5.1 TEST: Mode 71
- 5.5.2 TEST: BERT 71
- 5.5.2.1 TEST: Pattern 71
- 5.6 SELECT: Monitor 72
- 5.6.1 Monitor: Live-Alarms 72
- 5.6.3 Monitor: Rx-Params 73
- 5.6.4 Monitor: IP-Stats 74
- 5.7 SELECT: Store/Ld 75
- (Store/Load:) Override 75
- 5.8 SELECT: Utility 76
- 5.8.1 Utilities: Set-RTC 76
- 5.8.3 Utilities: 1:1 76
- 5.8.5 Utilities: Circuit-ID 77
- 5.8.6 Utilities: Firmware 78
- 5.9 SELECT: ODU 79
- 5.9.1 ODU: (BUC:) BUC_LO 79
- 5.9.1.1 ODU: (BUC:) Power 80
- 5.9.1.2 ODU: (BUC:) 10M-Ref 80
- 5.9.1.3 ODU: (BUC) Alarm 80
- 5.9.1.4 ODU: (BUC) Monitor 80
- 5.9.1.5 ODU: (LNB) LNB_LO 80
- 5.9.1.6 ODU: (LNB) 22K-Tone 81
- 5.9.1.7 ODU: (LNB) Polarity 81
- 5.10 SELECT: FAST 82
- 5.10.1 FAST: Options 82
- 5.10.2 FAST: Configure 82
- 5.10.3 FAST: Demo-Mode 83
- Chapter 6. ETHERNET 85
- MANAGEMENT 85
- 6.4 Telnet Interface 87
- 6.5.2 Web Server Menu Tree 88
- 6.5.3 User Login 89
- 6.5.4.1 Home (Splash) Page 90
- 6.5.4.2 Management Pages 91
- Slot Information 95
- Firmware Configuration 95
- 6.5.4.3 Network Pages 97
- Negotiated Link Mode 98
- Management Gateway Port 98
- LNB Freq (MHz) 100
- Rx Freq (MHz) 100
- Symbol Rate (ksps) 100
- Data Rate (kbps) read-only 100
- Current Routes – Tuner 1 102
- Add PID 103
- Tx Freq (MHz) 104
- Tx Interface Type 104
- Tx FEC Type 104
- Tx Modulation Type 104
- Modulator Section 104
- 6.5.4.7 Statistics Pages 107
- 6.5.4.8 Monitor Page 111
- 6.5.4.9 Utility Page 112
- Tuner 1 Constellation 113
- Appendix A. REMOTE CONTROL 115
- A.4 Packet Structure 116
- A.4.1 Start of Packet 116
- A.4.2 Target Address 116
- A.4.3 Address Delimiter 116
- A.4.4 Instruction Code 116
- A.4.7 End of Packet 118
- A.5.1 Tx Parameters 120
- Remote Control MN-CDM740 121
- A.5.2 Rx Parameters 123
- A.5.3 Unit Parameters 126
- A.5.5 Modem Information 133
- Appendix B. FAST Activation 139
- Procedure 139
- B.2.1 Serial Number 140
- B.2.3 Enter Access Codes 140
- Appendix C. 1:1 Redundancy 141
- C.2 Introduction 142
- IMPOR TANT 143
- 1:1 Redundancy MN-CDM740 144
- METRIC CONVERSIONS 149
- Units of Length 149
- Temperature Conversions 149
- Units of Weight 149
- 480 • 333 • 2200 PHONE 150
- • 333 • 2161 FAX 150
Manuais e produtos relacionados com Equipamento Comtech-ef-data CDM-740
Equipamento Comtech-ef-data RCS10 Manual do Utilizador
(275 páginas)
(275 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais